Open Access Open Access  Restricted Access Subscription or Fee Access

Influence of SiC and Al2O3 Particulate Reinforcements on Metal-Metal Wear Behavior of Al6061 Alloy Hybrid Composites Produced by Stir Casting Method

K. Umanath, S.T. Selvamani, K. Natarajan, K. Palanikumar

Abstract


Dry sliding metal-metal wear behavior of Al6061 alloy, discontinuously reinforced with fine particles of SiC and Al2O3 are presented and discussed this paper. The discontinuously reinforced aluminum (DRA) alloy composites with 5-25% volume fractions of SiC and Al2O3 particulates were produced by stir casting method and using them test specimens were prepared. The dry sliding behavior of these  hybrid composite specimens and that of Al6061 unreinforced alloy at room temperature was investigated by using pin-on-disk wear testing machine over a load range of 29.43N-49.05N(3-5 kgf) for a total sliding distance of 1413m  at a constant sliding speed of 1.57m/s. The results show that, the reinforcement of the metal matrix with SiC and Al2O3 particulates upto a volume fraction of 25% reduces the wear rate at room temperature. Higher the volume fraction of the reinforcements lower was the rate of wear. The results also show that the wear of test specimens increase with increasing load and sliding distance. Also micro hardness of the specimens at the room temperature was measured before and after the wear tests by Vickers hardness testing machine.  The micro hardness of the hybrid composite test specimens increases with increasing volume fraction of particulates reinforcement. The optical micrographs taken for the micro structure analysis of the hybrid composite specimens show that the SiC and Al2O3 particulates are uniformly distributed in the matrix. It was also found from the optical micrographs that the porosity of the test specimens increases with the increasing volume fraction of particulate reinforcement. The wear surfaces were examined by scanning electron microscopy, which showed that the wear surface of the composite alloy was generally much rougher than that of the unreinforced alloy. Large grooved regions and cavities with ceramic particles were found on the worn surface of the composite alloy. This indicates an abrasive wear mechanism which is essentially a result of hard ceramic particles exposed on the worn surface. 


Keywords


Al6061alloys Hybrid Composites, Stir Casting, Wear Behavior of Composites

Full Text:

PDF

References


Srivatson.T.S., Meslet Al-Hajri., Smith.C., and Peyraroli.M., “The tensile response and fracture behavior of 2009 aluminum alloy metal matrix composite,” Materials Science and Engineering , 2003,A346, pp 91-100.

Izciler.M., and Muratoglu.M., “Wear behaviour of SiC reinforced 2124 Al alloy composite in RWAT system.” Mater Process Technology, 2002, 5867, pp 1–3.

Umanath.K., Mathi.K., and Natarajan.K., “Influence of Silicon Carbide Particulate Reinforcement on the Tensile Behavior of Al 6061 alloy Composite produced by Stir Casting Method,” Proceedings of International Conference on Automotive Materials& Manufacturing, ARAI Pune, 2010, 22, pp 235-242.

Umanath.K., Selvamani.S.T., Natarajan.K., and Palanikumar.K., “Influence of Silicon Carbide Particulate Reinforcement on the Fracture Toughness of Al 6061 Alloy Composites Produced by Stir Casting Method” Proceeding of the international conference on frontiers in automobile and mechanical engineering, Chennai, 2010, pp 45-50.

Stephens.J.R., “High Temperature metal matrix composites for future aerospace systems,” NASA TM 1987, pp 100-212.

Taya.M., and Arsenanult.R.J., “Metal Matrix composites” Thermo mechanical Behaviour, vol 4, 1989, Pergamon Press, Newyork.

Srivatsan.T.S, Meslet Al-Hajri Petraroli.M., Hotton.B., and Lam.P.C., “Influence of silicon carbide particulate reinforcement on quasi static and cyclic fatigue fracture behavior of 6061 aluminum alloy composites,” Materials Science and Engineering , 2002,A325, pp 202–214.

Yang,J.B., Lin,C.B., Wang,T.C., and Chu.H.J., “The Tribological Characteristics of A356.2Al alloy/Gr_p_ Composites,” Wear, 2004, 257, pp 941– 952.

Yilmaz,O., and Butoz.S., “Abrasive Wear of Al2O3-reinforced Aluminium-Based MMCs,” Compos. Sci. Technol., 2001, 61, pp 2381–2392.

Caracostas.C.A., Chiou,W.A., Fine.M.E., and Cheng,H.S., “Tribological Properties of Aluminium Alloy Matrix TiB2 Composite Prepared by In-Situ Processing,” Metall. Mater. Trans., 1997, 28A, pp 491–502.

Tjong.S.C., and Lau.K.C., “Dry Sliding Wear of TiB2 Particle Reinforced Aluminium Alloy Composites,” Mater. Sci. Technol., 2000, 16, pp 99–102.

Ma.Z.Y., Liang.Y.N., Zhang.Y.Z., Lu.Y.X., and Bi.J., “Sliding Wear Behaviour of SiC Particle Reinforced 2024 Aluminium Alloy,” Mater. Sci. Technol., 1996, 12, pp 751–756.

Hahsins.J., Loonay.L., Hashni.M.S.J., “Metal Matrix Composites Production by stir casting method,” Materials Processing and Technology, 1999,92, pp 1-7.

Naher.S., Babazon.D., Loonay.L., “Simulation of the stir casting Process,” Material Processing Technology, 2003,30, pp 76-95.


Refbacks

  • There are currently no refbacks.