Open Access Open Access  Restricted Access Subscription or Fee Access

Synthesis and Characterization of Nano SiCp

S. Krishna Mohan, Dr.S. Ramanathan

Abstract


Silicon carbide powder (SiCp) was milled in a high energy ball mill in 350 rpm for 8 hrs. The wet milling media was tungsten balls (WC) in chemical compound Toluene (C6H6-CH3).The milled powder then characterized by Atomic Force Microscope (AFM) to study topography and particle size analyzer.

Keywords


Atomic Force Microscope, Particle Size Analyzer, Planetary Mill, Silicon Carbide and Synthesis.

Full Text:

PDF

References


Xiaolei S,Wancheng Z, Zhimin L, Fa L, Hongliang D, Dongmei Z. Preparation and dielectric properties of B-doped SiC powders by combustion synthesis. Mater Res Bull 2009; 44:880-4.

Maitre A, Vande Put A, Laval JP, Valette S, Trolliard G, Role of boron on the Spark Plasma Sintering of an α-SiC powder. J Eur Ceram Soc 2008;28:1881-90

F. Tang, M. Hagiwara, J.M.Schoenung, Mater. Sci. Eng. A 407(1-2) (2005) 306-314.

F. Tang, B.Q. Han, M. Hagiwara, in: A.C. Venetti (Ed.), Progress in Materials Science Research, Nova Science publishers, Inc., New TYork, 2008, pp. 131 – 158.

X.N. Zhang, L. Geng, G.S. Wnag, J. Mater. Technol. 176 (1-3) (2006) 146 – 151.

S.C. Tjong, Adv.Eng.Mater. 9(8) (2007) 639- 652.

S. Kleiner, F. Bertocco, F.A. Khalid, O. Beffort, Adv. Eng. Mater. 7 (5) (2005) 380-383.

G. Schwier, I. Teusel , M.H. Lewis, Characterization of SiC powders and the influence of powder properties on sintering (technical report), Pure Appl. Chem. 69 (6) (1997) 1305-1316.

D.W. Richerson, Modern Ceramic Engineering : Properties, Processing and Use in Design, Ed. Marcel Dekker, 2 Ed. Revised and Expanded (1992).

K.Niihara, New design concept of structural ceramics-ceramic nano-composites, J. Ceram. Soc. Jpn. 99(10) (1991) 974-982.

T.Ohji, A. Nakahira, T. Hirano, K. Niihara, Tensile creep behavior of alumina/silicon carbide nanocomposite, J. Am. Ceram. Soc 77 (12) (1994) 3259 -3262.

C. E. Borsa, N.M.R. Jones, R.J. Brook, R.I. Todd, Influence of processing on the microstructural development and flexure strength of Al2O3/SiC nanocomposites, J. Eur. Ceram. Soc. 17 (1997) 865-872.

J. Perez-Riguerio, J.Y. Pastor, J. Llorca, M. Elices, P. Miranzo, J.S. Moya, Revisiting the mechanical behavior of alumina/silicon carbide nanocomposites, Acta Mater. 46(15) (1998) 5399-5411.

A.J. Winn, R.I. Todd, Microstructural requirements for alumina- SiC nanocomposites, Br. Ceram. Trans. 98(5) (1999) 219-224.

L.P.Ferroni, G. Pezzotti, Evidence for bulk residual stress strengthening in Al2O3/SiC nanocomposites, J. Am. Ceram. Soc. 85(8) (2002) 2033-2038.

D.Sciti, J. Vicens, A. Bellosi, Microstructure and properties of alumina SiC nanocomposites prepared from ultrafine powders, J. Mater. Sci. 37 (2002) 3747-3758.

A.M.Thompson, H.M. Chan, M.P.Harmer, Tensile creep of alumina / silicon carbide nanocomposite, J. Am. Ceram. Soc. 80(9) (1997) 2221-2228.

C.E. Borsa, S. Jiao, R.I.Todd, R.J. Brook, Processing and properties of Al2O3/SiC nanocomposites, J. Microsc. 177(3) (1995) 305- 312.

M. Sternitzke, Review: structural ceramic nanocomposites, J. Eur. Ceram. Soc. 17 (1997) 1061-1082.

H. Berthiaux, J. Dodds, Modelling fine grinding in a fluidized bed opposed jet mill – part –I; batch grinding kinetics, Powder Technol. 106 (1999) 78-87.

H.W. Hennicke, J. Stein, Process of fine milling for ceramics materials, Mater. Sci. Eng., A 109 (1989) 3-7.

C.Suryanarayana, Mechanical alloying and milling, Prog. Mater. Sci. 46 (2001) 1-184.

F.V.Brito, Procesamento de Meios Porosos à Base de silica, M.Sc Thesis, PEMM-COPPE- UFRJ, Rio de Janeiro-RJ-Brasil-Dezembro(2004).




DOI: http://dx.doi.org/10.36039/AA072012010

Refbacks

  • There are currently no refbacks.


Creative Commons License
This work is licensed under a Creative Commons Attribution 3.0 License.